Boatneck top – New Look 6838 finished

Hi, it’s been an overcast and rainy week so I decided to take photos of this boatneck top inside. The photos are pretty boring but at least you can see the finished New Look 6838 top. I wore it to work so it’s a little wrinkled from sitting this morning.

Boatneck top - New Look 6838 - CSews.com

Version A has 3/4 length sleeves but as I noted in yesterday’s post about the pattern, the sleeve pattern piece was quite long. After I sewed and hemmed the sleeves, the hem was about an inch above my wrist bone. So I cut about 5 inches from the length and hemmed them again to make them the current length. And I have long arms so if you have average-length arms, the 3/4 sleeves will be long sleeves on you.

I put my finished sleeve next to the pattern piece. Here’s how much I lopped off.

New Look 6838

The houndstooth knit fabric doesn’t have very good recovery so I think the boat neck neckline will likely get stretched out. You can already see that in the front it doesn’t quite lie flat. But this was my mockup so it doesn’t really matter.

Boatneck top - New Look 6838 - CSews.com

One common complaint in the Pattern Review reviews for this pattern was that the boatneck neckline was too wide. I didn’t make any changes to the front. The width was about 3/4 inch too wide for me – even with my broad shoulders. You can see that the shoulder seamline droops a bit off my shoulder bone.

New Look 6838 - boatneck top - CSews.com

I do like the neckline because it reveals my collar bones. However, the width also reveals your bra straps. If I make it again, I’ll need to sew in bra strap holders at the shoulders and make the shoulders a little more narrow, which will be a first for me. I often do a wide shoulder adjustment.

Boatneck top – back view

This top has a center back seam, which seemed a bit unusual for a knit pattern. I decided to go with it and see what that would look like. My fabric has a tiny houndstooth print but I didn’t bother trying to match the print. The knit print was a leftover scrap from making Vogue 9191 wrap pants in 2016.

Boatneck top - New Look 6838 - CSews.com

The seam curves out slightly at the bottom to give some shaping but I think you could just eliminate the seam allowance and cut it on the fold – unless you have a booty that would benefit from the curve.

Side view

You can really see the droopy shoulder here – partly because the top was shifting because the neck opening is a little too wide. It doesn’t quite droop this much. If I center the top, it’s about 3/4 inch off.

Boatneck top - New Look 6838 - CSews.com

I did stabilize the hem with fusible stay tape but as you can see the hem is a little rippled. I used a twin needle but I haven’t pressed the hem. Maybe it’ll be a little flatter after pressing.

Here’s another view of the left side.

Boatneck top - New Look 6838 - CSews.com

Here’s a look at the right side of this boatneck top. I pulled down the back to smooth out the wrinkles and pulled down the neckline back there. So it looks like the hem is lower in the back but it’s not drafted as a high-low top. The hem is actually the same length front and back.

Boatneck top - New Look 6838 - CSews.com

Making it again

I will certainly make this boatneck top pattern again because I like the bateau neckline. I will bring in the shoulders about 3/4 inch and shorten the sleeves by 5 inches. I’ll pick a medium weight jersey with good recovery and make sure I test fusible stay tapes and whether I should use a double needle or just a zigzag stitch, whichever will look better. (I don’t have a cover stitch machine.)

I’m not sure if I’ll keep that center back seam. This pattern could be a good stash buster. You could have fun color blocking it – using different colors for the back, sleeves and front.